Until a couple of weeks ago, I’d never heard the name NOUS – but now I have, I’m glad of it.I enquired for samples to demo in here and they quicky send off several of their devices – great stuff, slightly marred by an incompetent courier here in Spain who dumped the goods at some arbitrary shop in the village, causing grief for both myself and Nous.I’ve suggested they avoid that particular courier in future.
Firstly – the Nous Zigbee 9w smart bulbs This evening I picked up the goods and over the weekend I’ll write something about them, maybe put together a short video.Meanwhile, among other things, they sent me a 4-pack of Nous-brand 9W RGBCTT E27 bulbs (i.e.RGB + temperature-variable white).
Timing could not have been better as I’ve just been updating Home Assistant and one of my office lights failed – something that doesn’t happen a lot.I tried everything including checking the WiFi access point to no avail.I recalled the now-defunct lamp is called COSTCO-2 – and on going back through the blog realised this is/was a FEIT RGBCTT light I blogged back in June 2020 and like others in my office, the light has been on most days all day since then – that’s 5 years – can’t complain.
The Costco light is one I immediately converted to Tasmota when I got it and thankfully I can check Tasmota lights independently of HA using TDM (Tasmota Device Manager).Definitely shot, not even putting up its’ own access point.Ok, so deep dive into the new NOUS bulbs – these are Zigbee 3.0 – I pulled one out of the pack – plugged it in (the lights initaially flash for setup – nothing to do on the light itself) – set my Zigbee2MQTT to accept new devices and a new device with the usual long-winded numerical ID appeared.
I ran the RENAME command in Zigbee2MQTT (which has a spiffy new interface in Home Assistant incidentally) and..It turns out that Zigbee2MQTT knows all about NOUS and accepted the bulb immediately.Options include state, brightness, color temp, color, effect, do not disturb, color power behaviour (i.e.
power on behaviour) – and well, that’s it – to be expected.I’m using “color” as that’s how they spell it – being British I’d normally call it “colour”.I set the light to full-on warm-white as well as “previous” for power-on behaviour.
Great start and got me out of a jam – absolutely no hassle.I named the lamp nous-rgb-1 and decided to call it a night after installing this lamp, as I need an adaptor before I can close up the lamp because the Costco light was UK Bayonet and the light fitting is E14 while this particular nous-rgb-1 device is E27 size.All I had to do was change a lamp ID and an”office lights” helper group reference in HA – to point to the new light.
Tomorrow the slightly trickier purchase of an E14 to E27 lamp adaptor.Actually that pretty much wraps up their RGB lights – they are of average brilliance for a (total) 9w lamp and it acually says on the box that they will work with Zigbee2MQTT (for the un-initiated, that’s completely local wireless – see the Zigbee2MQTT website for more).I should say the colour performance is better than many AliExpress-type RGB lights I’ve had, some or which have had adequate white but abysmal colour.
These new lamps are just fine.Next – the Nous Smart Tasmota WiFi Socket – Nous A8T Being pre-fitted with Tasmota – setup could not be easier.I plugged in the socket to an extension and a nice blue light in the centre of the manual on-off side-button started to flash – exactly as I would expect from Tasmota.
On my Android phone I went looking for a new access point with a name starting with tasmota – I found one and selected it.I told it about my normal 2.4Ghz WiFi access point at which point seconds later I was told to reconnect to my normal Wifi and the device would be at address 192.168.1.147.It was.
As you can see, right, the smartplug has a maximum capacity of 2300W (that’ll be non-inductive load) and as well as the Nous branding, shows Tasmota on the front.The very first thing I usually do at this point – is to change the name – I wanted this to be called nous-a8t-1 I could have continued setup on my phone but I chose to do it in a browser on the PC – just by entering that IP address.As you can immediately see, with no APP, just the built-in webUI in a browser (Chrome in my case), you have full control over the tasmota device – toggle on-off, configuration, information, firmware upgrade and consoles (plural).
The latter tells you that this is ESP32-based.The A8T does full power-monitoring and also shows the ESP32 temperature in the webUI.58c is quite normal.
See below.So, without any setup, the device is just called Tasmota – it needs a name change before you proceed to setup/use any similar devices.The setup can be done in “configuration” but as I’ve done this many times, I’m going to go to “consoles” and the first entry “console”.
In there I’ll enter everything in one long line… but of course you can go into configuration and set details individually – this is all covered on the Tasmota website and in numerous entries in my blog website.I also use a setoption 53 – and set it to 1 so I can see the IP address in the webUI, but that’s just my preference.So the console command for that is simply so53 1 I also tell it about my MQTT broker and it’s username and password (not everyone uses an MQTT username and password) – and MQTT is not needed for these devices to work, though it helps for Home Assistant integration The important thing is to set the hostname under “configure WiFi” and again set the friendlyname under “configure other” You can configure MATTER (I have no need for that as the socket will be used by Home Assistant and the MQTT configuration makes the device appear automatically therein).
There is a TON of optional configuration.Note in the configuration page below right you are seeing the new name I’ve given the device – “nous-a8t-1” – I could have used something like “corner-shelf-light” but I prefer something that tells me that the device is rather than what it does.Note that the power monitoring is pre-configured.
My device came with Tasmota32 version 13.3 and I could not stop myself from using the built-in OTA firmware upgrade option and moments later without touching anything, I had bang-up-to date Tasmota running on my new smartplug.(see at the bottom of the config image right “”Tasmota 15.0.1” You should be aware that Tasmota is totally open-source, fully local and very well supported by the autgor and the Tasmota community – and has been around for years.I developed my own firmware for ESP8266 devices years ago – it was good but ultimately moved to Tasmota because of the support it gets – and still gets in the ESP32 versions today.
It is absolutely un-necessary to upgrade the formware but I just like to be up to date.It’s all down now to erliability and I can only say that the Nous A8T looks solidly built (and very pretty).To describe the possible features of a Tasmota-driven plug like this would take a LONG time but suffice it to say you have timers 7-day with repeat and sunrise-sunset and offset options – and if that isn’t enough you have a full set of powerful rules and more.
In another article you;ll see me using a Tasmota smart plug as a router power-reset watchdog.If you don’t like the standard colours in the webUI you can always go here – and to see the many, many commands you can use in Tasmota go here.Of course you can ignore all of this and just use the A8T as a simple smartplug – but then you’d be missing out on so much.
Remember that because Tasmota runs locally, in order to access a Tasmota-based device’s webUI when away from home or the office, you’ll need to use a VPN.My VPN of choice is the free, easy to use and powerful Tailscale, running on my GL-iNet router.No installation needed on the smartplug.
So now I’ve told you about two Nous products – a Zigbee2MQTT-based lamp and a Tasmota-based smartplug – there is much more but I think I’ll split this blog up – I’ve lots of other devices that they sent to me – to show you – more over the weekend.For now, I’m so glad I discovered this company – and no they are not paying me nor did I HAVE to create positive reviews.It just worked out that way.
Before stopping for now, I noted that Nous make some of their oen products and brand others – if this interests you, their website no doubt provides detail..
